Cold wash only available with some models For washing lightly soiled or color-sensitive laundry. When this function is activated, the heaters in the washing machine are turned off, and the washing program is shortened. Higher water level Improves rinsing, which is particularly important if your skin is oversensitive to detergents.
For washing heavily soiled laundry. Auto-clean program SterilTub Run this program to eliminate any impurities, bacteria, and odor from the washing machine.
Before running the auto-clean SterilTub program, empty the washing machine drum; there shouldnt be any clothes in the washing machine during the auto-clean SterilTub program. Adding a small amount of powder detergent will additionally improve the effect of the auto-clean SterilTub program.
To run the auto-clean SterilTub program, rotate the program selector knob A to the position Cotton 95C, then pressing the E Higher water level key and hold it for three seconds. Cln and the time remaining until the end of the program will alternate on the display.
If you do not regularly use washing program with temperatures over 60C, it is recommended to run the auto-clean program at least once per month. These are independent programs and may be used when you do not need the entire washing program. In case you would like to use more additional programs in a sequence, you must turn off the appliance prior any new program selection turn the program selector to 0 for at least one second. Rinsing Independent program for rinsing sensitive laundry, without spinning between individual rinsing cycles and with a short nal spinning.
It can be used for rinsing manually washed sensitive laundry. Spinning speed rpm can be decreased. Conditioning This program is intended for conditioning, starching, or impregnating washed laundry. It is completed by spinning at a maximum of rounds per minute. Spinning speed can be decreased. Pumping the water out Use it when the washing program was interrupted or if pump stop function was engaged, and you only wish to pump the water out of the drum, without spinning.
Spinning Aggressive spinning for non-delicate laundry at high spin RMP. You may engage the reduced spin RPM knob.
When adding softener, be careful to ll the dispenser only up to the marked level. Sound signal conrms the start, the LED indicating particular washing stages stops ashing. The machine starts operating after a few seconds. If the door is not properly closed after starting the operation, the washing stage indicator LED starts ashing again after a few seconds. When you close the door, the machine initiates the selected program. As each washing stage is completed the relevant washing stage indicator LED goes off and the subsequent one goes on.
In case you would like to alter the washing program after the initiated washing operation, turn the program selector for one second to the position 0, followed by the selection of a new program. Switching the machine off deletes any previously selected additional functions i.
Pump stop , so they have to be reactivated. Upon switching OFF, all additional pre-selected functions are deleted; therefore they must be switchedON again. The message End is indicated on the display. A sound is emitted, indicating that washing machine door can be opened. Take the laundry out of the drum and remove any remaining particles or foreign bodies from the door seal. Leave the door ajar to let the machine dry. Close the water inlet tap.
Turn off the washing machine by rotating the program selector knob A to position 0. After the end of washing program, power supply should be turned off by pulling the mains cord plug out of the outlet. The LED over the button C starts to ash. The program can be completed by pressing the START F button; in this case, the program will nish with a spinning cycle, as dened by the program.
The program can also be changed by rotating the program selector knob to 0 and choosing either spinning or only pumping out the water between additional programs or cycles. Manual cancellation The program is cancelled if the program selector knob A is rotated to position 0. If there is water in the machine, select one of the additional programs pumping , spinning to empty the drum and complete the program. After certain time you may open the door if there is no water in the drum, otherwise this is not possible.
Failures Program is suspended in case a failure occurs. Signal LEDs are ashing and sound signal is heard see cf. Power failure At electric cutout the program is interrupted, however, after the power supply has been re-established, the program operation automatically proceeds. If a power failure occurs when the drum is still full of water, be careful not to open the door before you pump the water out.
Child lock - To activate the child lock, simultaneously press the spinning button C and short program or cold speed setting wash button D and hold them for at least three seconds.
If the child lock is successfully activated, a sound is emitted and a signal LED lights up. Follow the same procedure to deactivate the lock. You may merely switch off the machine by turning the program selector A to the position 0. Child lock remains active even after the appliance is switched off, and you have to disengage it if you want to select a new washing program.
Setting the sound signal The appliance enables setting a louder sound signal, as well as turning the sound signal off. Set the function before the. Set the function by simultaneously pressing the button D and rotating the program selector knob A from position 0 to the rst position for washing program clockwise.
S1 is indicated on the display, denoting preset normal sound signal loudness. By pressing the button D , the loudness in increased S2 ; press the button again to turn the sound signal off S0. The selected setting is stored and remains in memory even if washing machine is turned off. Tips for washing and energy saving Before washing sort out the laundry according to the type, degree of dirtiness and color resistance.
Prior selecting the washing program consult the sewn tab with information on a particular piece of laundry see Maintenance Chart on the last page. Wash separately the new colored textile products for the rst time. Wash heavily soiled laundry in small quantities and add more detergent. Treat stubborn stains with special stain remover, it will save energy.
With lightly stained laundry select washing program without pre-wash, use short program and select lower washing temperature. Avoid washing too little quantities of laundry because of energy saving and for better performances of the appliance. The largest allowed quantity of dry laundry is indicated in the Program chart. Before washing empty the pockets, close zip fasteners, and remove any metal fasteners or badges that might clog the drain or damage the laundry or drum interior.
Loosen the stacked laundry prior inserting it into the drum. Use only detergents for machine wash. Add powder or liquid detergents according to the manufacturers instructions.
For different washing temperatures and selected washing programs, please note the recommendations provided by detergent manufacturers. If water hardness level exceeds 14dH degrees, the use of water conditioner is required. Any damage to the heater due to failure to use a water conditioning agent shall not be covered by this warranty. Chlorine-based whitening agents are not recommended, as it can damage the heater.
In case of hard water add detergent according to the Chart for degree 1 and add appropriate quantity of water softener see manufacturers instructions. If you do not apply the program which includes the pre-wash feature, you may add washing detergent directly into the drum. If you use thick liquid softener it is recommended to dilute it with water, to prevent clogging of dispenser compartment ducts.
Washing machine is equipped with the dispenser partition gate, so you may pour liquid detergent also into the central compartment depending on model. If you use powder detergent the gate is lifted up, and in case of liquid detergent it is slid down. Liquid detergents are intended for main wash only, without pre-wash.
Insert particularly delicate linen stockings, delicate female underwear, etc. High spin RPM leave less moisture in laundry which dries out much quicker in the tumble dryer, thereby saving energy.
Do not put clods of detergent into the soap dispenser as the tube in the washing machine may clog. Cleaning and maintenance Disconnect the washing machine from the mains before cleaning!
The casing should be cleaned with soft cloth and mild detergent. The interior of the drum and the door gasket is cleaned by washing at 60C without laundry and adding half quantity of detergent. Frequent, or predominant, washing at low temperatures, using liquid detergents, may result in development of bacteria which causes odor in the washing machine. If necessary, clean the detergent dispenser.
Pull it out from its casing completely by pressing the ap see Fig. Wash it under running water using a brush, and dry it. Remove any leftover dried detergent from the bottom of the casing. Clean the entire rinsing area of the washing machine with a brush, especially the nozzles on the upper side of the rinsing chamber. Clean frequently the water inlet hose screen under running water. After each wash wipe the door rubber gasket. This will prolong its useful life.
Filter needs occasional cleaning, especially following heavily shaggy or old laundry. Before cleaning, drain any water from the machine via drain pipe. Insert the lter back as shown on the picture, and tighten by turning it in clockwise direction.
To ensure good sealing the gasket surface A must be dirt free. Troubleshooting Washing machine controls the operation of particular functions during washing.
If irregularities are detected, the fault is signaled by displaying a message Fx on the display, and by rhythmical ashing of the LEDs. Simultaneously with the ashing of the LEDs, a sound signal is emitted several times, in the same rhythm. The machine signals the fault as soon as it is detected, and the program progress is paused. If the fault is in the heating system, the machine completes the washing program, but without the heating function. If the fault is signaled during washing machine operation, the error code and remaining washing time are indicated alternately on the display.
The fault is indicated until the washing machine is turned off. Failures: 2 - Two ashes: door is not correctly closed 3 - Three ashes: inappropriate water intake 7 - Seven ashes: inappropriate water outlet. In these cases, you will be able to remedy the failure by yourself See Troubleshooting table. If the failure persists, contact the nearest authorized service centre the LEDs will continue to ash until the appliance is turned off.
Various interferences from the environment e. In such case: - turn off the appliance and wait a few seconds; - turn on the appliance and repeat the washing program.
If the fault reoccurs, call the service center. The warranty does not cover faults caused by interference from the environment lightning strike, electric circuit, natural disasters, etc. Failure The machine does not work indicator LEDs are not illuminated. Water is leaking from the machine. Remedy Check if: power in the socket, the fuse is OK, plug is in the socket. Push it towards the machine. Filter is not tightly screwed in. Inlet pipe is not tightly screwed to the machine or to the water faucet.
Outlet pipe fell to the oor. The machine is not properly leveled. Transport brackets are not removed. Unevenly distributed laundry, especially with very small quantities for ex.
Excessive measure of detergent. Tighten the lter properly. Tighten the inlet pipe. Afx the outlet pipe to the drain. Level the machine with the adjustable legs. Remove transport brackets.
This is normal, the machine will reduce the RPM if vibrations are too strong. Wash larger quantity of laundry. Use washing powder according to the instructions by the producer and according to the water hardness and soiled laundry.
Use only detergents for machine washing. Check if: the lter is clean, outlet pipe is not jammed, the drain is clogged, outlet pipe is positioned higher than 1m. Wash large and small pieces of laundry together. Gorenje WA specifications. Related product manuals. What temperature should I use for my laundry? The washing label of your garment shows the recommended washing temperature. Do I need to use an anti-scaling agent for my washing machine? It is not necessary to use an anti-scaling agent.
Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash. How do I prevent my washing machine from smelling? Unpleasant odours can be avoided by occasionally washing at 60 degrees and using the recommended amount of detergent per wash. About the Gorenje WA Gorenje WA specifications. Related product manuals.
What temperature should I use for my laundry? The washing label of your garment shows the recommended washing temperature. Do I need to use an anti-scaling agent for my washing machine? It is not necessary to use an anti-scaling agent. Scale deposits can be prevented by limiting washing at high temperatures and using the recommended amount of detergent per wash. How do I prevent my washing machine from smelling?
0コメント